tom eaton wrote on Tue, 30 September 2008 16:12 |
well, I had hoped they would have commented here already... |
tom eaton wrote on Mon, 06 October 2008 15:07 |
Getting ready to shell out for two RME cards so I can use my Apogee converters with my G5. Not at all what I expected when I got on the Symphony boat. edit: or, after some pondering... perhaps four motu 2408mkIII units running s/mux for 48 i/o at 96k via my one motu pci424 card. that would keep me using the motu cue mix software which I like. this is way more complicated than it should be. t |
Tomas Danko wrote on Tue, 07 October 2008 07:37 |
There are RME solutions where you can get lots of channels and it all merges inside one single TotalMix. |
tom eaton wrote on Tue, 07 October 2008 14:14 | ||
For the record, are you talking about MADI? I did consider that route. tom |
compasspnt wrote on Fri, 06 March 2009 08:55 |
If one is going to change the internal jumper so that the units power on at mains application... Is this something in the manual, or is there a special technique, or extraordinary knowledge required? |
compasspnt wrote on Fri, 06 March 2009 11:11 |
Now I just need some of those silly metric screws! |
Phil Mayor wrote on Sat, 31 January 2009 22:38 |
ha..just spotted this thread. I have the dreaded DA/AD16x switch problem too.. |
marcel wrote on Tue, 17 March 2009 15:42 |
Anyone have any experience with the X-HD cards, which allow direct interface to PTHD? I was hoping to go this route later this year but if they're as sketchy as the X-FW and Symphony stuff I may have to re-think. JJ, you're not using PT interfaces, are you? Or are they just hidden in your rack pic? |
rankus wrote on Mon, 16 March 2009 19:30 |
Hopefully my costly adventure will save others $ pain and grief! Thanks Apogee |
J.J. Blair wrote on Mon, 23 March 2009 01:46 |
I have the cards installed in my converters so that I can connect them directly to my PTHD cards. Works flawlessly. |
BrianS wrote on Mon, 23 March 2009 08:58 | ||
Same here. No problems. |
rankus wrote on Fri, 06 March 2009 18:14 | ||
Apogee sent me some by mail at no cost when I asked them "what was up with that" CALL: 310 584-9394 - Jay is a nice guy in support... |
Fibes wrote on Mon, 13 April 2009 08:59 |
After reading this thread and watching issues with a Prism dream system I'm wondering if there is ever gonna be a good mobile system for me that will work in the studio as well. Tom, I guess MOTU Cuemix is hard to beat isn't it? You'd think Apogee could but... |
J.J. Blair wrote on Tue, 21 April 2009 20:26 |
I just got an e-mail from Lucas at Apogee: "Just an update on the status of the switches. We located a more heat resistant version and they are on order. So probably somewhere next week we'll have them. I'll let you know when they're in and we can set you up for a replacement." Goddamn those units get hot! Some op amps are being run class A, as I learned, and that makes it even hotter. |
tom eaton wrote on Wed, 15 April 2009 06:45 |
If Apogee wanted to copy Metric Halo there would be a mixer that was usable in one of their products. And great processing. |
tom eaton wrote on Mon, 04 May 2009 06:37 |
Agreed, I think there is a reason we all deal with the other issues. It does finally come down to the fact that they sound great. tom |
J.J. Blair wrote on Sun, 10 May 2009 17:35 |
Nacho, is there a driver you have to download to get it to work with Windows? that's usually the case to get ANYTHING to work with Windows. |