R/E/P Community

Please login or register.

Login with username, password and session length
Advanced search  

Pages: 1 [2]  All   Go Down

Author Topic: RE-20 Repair  (Read 7922 times)

Fenris Wulf

  • Sr. Member
  • ****
  • Offline Offline
  • Posts: 499
Re: RE-20 Repair
« Reply #15 on: August 20, 2010, 12:31:55 am »

Here's where I ordered the wrench:

http://buy1.snapon.com/catalog/item.asp?item_ID=72224&gr oup_ID=585
Logged
RESIST THE CYBERNETIC OVERLORDS
KDVS Studio A

robft

  • Newbie
  • *
  • Offline Offline
  • Posts: 5
Re: RE-20 Repair
« Reply #16 on: December 17, 2010, 01:51:28 am »

After you get the top off, can you pull the capsule out (are the internal wires long enough) or do you have to take the back plate off and unsolder the wires before replacing the foam? Or will the backplate slide out too?
Logged

Fenris Wulf

  • Sr. Member
  • ****
  • Offline Offline
  • Posts: 499
Re: RE-20 Repair
« Reply #17 on: January 25, 2011, 11:27:29 am »

The shockmounts for RE-20's are supposed to swivel, but the little thumbscrew eventually works its way loose and the mic crashes onto the broadcast console and breaks off a fader.  Mad  Any suggestions for immobilizing the thumbscrew? Loctite?
Logged
RESIST THE CYBERNETIC OVERLORDS
KDVS Studio A

zebra50

  • Newbie
  • *
  • Offline Offline
  • Posts: 46
Re: RE-20 Repair
« Reply #18 on: January 25, 2011, 06:55:05 pm »

Quote:

After you get the top off, can you pull the capsule out (are the internal wires long enough) or do you have to take the back plate off and unsolder the wires before replacing the foam? Or will the backplate slide out too?


I've just done one of these. You do need to take off the backplate, but it's not hard. Follow the photo tutorial earlier in the thread - it's really helpful.
Logged
Stewart Tavener
Xaudia - studio, ribbon mic repairs
http://www.xaudia.co.uk

Garrett H

  • Sr. Member
  • ****
  • Offline Offline
  • Posts: 406
Re: RE-20 Repair
« Reply #19 on: February 04, 2011, 06:30:41 pm »

Our RE-20 gave us troubles.  Fine on quiet things but distorting on any serious levels.   So, we called EV and asked for a quote.  Someone on one of these boards said they were easy to deal with and expecting such we gave them a ring.   They said they wanted $250 to LOOK AT THE MIC and, they would tell us what was going on before any work proceeded.  The $250 would go towards the repair costs, but the labor could go past that.  Shipping both ways was on us.

?

Fortunately, I found a gentleman at micdaddy.com from Lincoln, Nebraska, who quoted me $159.   We shipped him the mic, he fixed it blew a new powder coat, baked it and had it back to me in days.  The mic sounds wonderful again.   So, I give micdaddy.com a hearty well done if your RE-20 needs some love.

micdaddy.com <http://micdaddy.com/>  

Logged
Treelady Studios, Pittsburgh, PA
http://www.treelady.com
Senior Contributor, Tape Op Magazine
http://www.tapeop.com

klaus

  • Moderator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1423
Re: RE-20 Repair
« Reply #20 on: June 04, 2015, 02:23:25 am »

Quote
Fortunately, I found a gentleman at micdaddy.com from Lincoln, Nebraska, who quoted me $159.   We shipped him the mic, he fixed it blew a new powder coat, baked it and had it back to me in days.  The mic sounds wonderful again.   So, I give micdaddy.com a hearty well done if your RE-20 needs some love.
micdaddy.com <<a href="http://micdaddy.com/" target="_blank">http://micdaddy.com/</a>>

However, I saw this thread about "micdaddy's" services- specifically post #8:
https://www.gearslutz.com/board/so-much-gear-so-little-time/897053-micdaddy-com-ev-mic-repair.html

It is not easy to determine the veracity of the claims in the quoted thread, but I thought that there were enough complaints of a similar nature that it warranted a notice here, so that the previous post of recommendation for this service provider can be viewed in the context of the experience of others.
Logged
Klaus Heyne
German MasterworksŪ
www.GermanMasterworks.com
Pages: 1 [2]  All   Go Up